A 2.36 inch SS304 welded wire mesh panel is a stainless steel grid with a nominal mesh opening of 2.36 inches, approximately 60 mm, and wires joined at their intersections by welding. SS304 identifies the stainless steel grade, while the opening size alone does not define the panel: wire diameter, panel dimensions, opening measurement method, and tolerances also matter. We recommend confirming these details before comparing quotations so you can assess fit, strength, finish, and cost against your project requirements. This guide explains what to specify and what to ask a supplier, including Shunqiang Wire Mesh.
This guide is for purchasing managers, engineers, fabricators, and project teams comparing stainless steel welded mesh panels for industrial, commercial, or general fabrication use. It is especially useful when a drawing, specification, or existing installation calls for an opening near 2.36 inches. If you are preparing a request for quotation, the checklist below can help you send suppliers comparable information. Final suitability should be confirmed against your design, applicable project requirements, and operating environment.
“2.36 inch” typically refers to the mesh opening, while “SS304” refers to the stainless steel grade used for the wires. A 2.36 inch dimension converts to approximately 59.94 mm, commonly rounded to 60 mm as a nominal metric value. However, a drawing may define the opening as a clear distance between adjacent wires or as a center-to-center pitch, and those interpretations produce different finished grids. We advise stating the measurement method explicitly rather than relying on the product name alone.
Welded mesh is formed by arranging wires in two directions and joining them at crossing points. The panel can provide a defined open area and a fixed grid format for fabrication or installation, but its load capacity cannot be judged from opening size alone. Wire diameter, panel span, support spacing, weld quality, and loading conditions all influence performance. Where the panel is safety-critical or load-bearing, have the design checked by a qualified engineer and specify the required performance criteria.
| Specification | What to state or confirm | Why it matters |
|---|---|---|
| Mesh opening | 2.36 inches (about 60 mm); clear opening or center-to-center pitch | Prevents ambiguity in spacing and finished panel dimensions. |
| Wire diameter | Required diameter, preferably shown in mm or inches | Affects rigidity, weight, open area, and fabrication requirements. |
| Panel dimensions | Finished width and length, with units and dimensional tolerances | Determines fit, handling, cutting, and shipment planning. |
| Material | SS304 and any required material documentation or inspection criteria | Helps align the delivered material with the purchase specification. |
| Finish and edges | Surface condition, cut-edge requirements, and any finishing request | Supports safe handling and consistency with the installation. |
| Quantity and delivery | Panel count, packaging, destination, and requested delivery schedule | Enables a meaningful quotation and production plan. |
For a material reference point, Type 304 stainless steel is commonly specified with chromium content of 18–20% and nickel content of 8–10.5% by mass under recognized product specifications. These ranges are not a substitute for confirming the applicable standard or checking the actual documentation for the ordered wire. If chemical composition, mechanical properties, or traceability are contractual requirements, list them in the inquiry and agree on acceptable documents before production.
A relatively open grid can be appropriate where airflow, visibility, or passage of material is important, but the same opening may be unsuitable when smaller particles must be retained. The intended function should guide the choice of wire diameter and support arrangement as well as the opening. For screens, guards, partitions, racks, or fabrication components, confirm how the panel will be supported and whether the edges need to fit a frame. Do not assume the nominal mesh size alone establishes safe performance.
SS304 is widely used where a stainless steel material is required, but corrosion resistance depends on the conditions of use. Exposure to chlorides, certain chemicals, high temperatures, or persistent moisture can affect material selection and service life. For coastal, chemical-processing, or other aggressive environments, provide the supplier with the exposure details and ask whether SS304 is suitable for the specific duty; a different grade or protective approach may need evaluation. We avoid treating any grade as universally corrosion-proof.
Shunqiang Wire Mesh contains other products and information you need, so please check it out.
Start by recording what the panel must do: retain material, provide separation, support an item, or serve as a fabricated component. Note the expected loads, contact materials, cleaning process, and environmental exposure where relevant. If the panel is part of a designed assembly, use the drawing and engineering specification as the controlling reference. This gives suppliers the context needed to discuss wire size and construction instead of quoting only a mesh opening.
State the opening as 2.36 inches or approximately 60 mm and define whether it is a clear opening or a pitch. Add wire diameter, panel length and width, number of panels, and any required dimensional tolerances. Identify whether the edges should be flush, trimmed, or left with projecting wires, and describe any cutouts or special fabrication. If you work in both metric and imperial units, designate one as the controlling unit to reduce conversion errors.
Specify SS304 and identify any applicable material standard, inspection requirement, or documentation needed for acceptance. Ask how the supplier will identify the material and what documents can be provided with the shipment; do not assume that a document is included unless it is agreed in the quotation or purchase order. Describe the required surface condition and any post-weld or edge treatment, if applicable. For visible or hygienic installations, explain the finish expectations and confirm whether the proposed finish meets them.
Compare suppliers using the same opening definition, wire diameter, panel dimensions, tolerances, grade, finish, and quantity. Review whether the price includes packaging, export preparation, inspection, and delivery terms, as these can change the total landed cost. Ask for minimum order quantity and lead time for the exact panel specification rather than relying on a general estimate. Confirm which details are fixed and which remain subject to final drawing approval.
The price of a welded wire mesh panel depends on material, wire diameter, panel size, order quantity, fabrication complexity, packaging, and delivery destination. A request specifying only “2.36 inch SS304 mesh” is usually insufficient for a reliable like-for-like comparison because key cost and production details remain undefined. Minimum order quantity and lead time can also vary with the requested dimensions, production schedule, and order volume. We recommend asking suppliers to quote the exact specification and state any assumptions or exclusions clearly.
At Shunqiang Wire Mesh, we support B2B buyers by reviewing requested mesh openings, material, wire diameter, panel dimensions, and delivery requirements for quotation. To help us assess your inquiry, send a drawing or specification sheet where available, along with the quantity, destination, and any documentation or finish requirements. We can then confirm which details need clarification before the order is placed. Any product scope, lead time, and supporting documents should be confirmed in the quotation.
A 2.36 inch SS304 welded wire mesh panel is defined by more than its nominal opening: the opening measurement method, wire diameter, panel dimensions, material requirements, finish, and edges all need to match the intended application. The most useful next step is to prepare a complete specification and request a quotation based on the same details from each supplier. Confirm suitability for the service environment and structural requirements before approving production. Contact Shunqiang Wire Mesh with your drawing, quantity, and delivery details to discuss a project-specific quotation.
Want more information on 2.36 inch ss304 welded wire mesh panel? Feel free to contact us.